Having a go at building a Fuzzrite, a few questions

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Sat Dec 25, 2010 6:02 pm

I have the Transistors, Resistors, etc that were described on Mr. Bill's list. Does anybody have any advice as to how big my perf board should be? I am following the schematic from fuzzcentral.


excuse my ignorance, but what is EBC? this is my first time attempting anything like this so i dont know what some of this stuff means.
Could somebody possibly post a finished photo of the guts of one of theirs? Thanks

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Sat Dec 25, 2010 9:13 pm

After a bit of research i answered the EBC question, but the perfboard dimension question still remains. And would it matter if I use Germanium transistors instead of the 2N3904s? Cheers

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Sun Dec 26, 2010 8:19 pm

After pulling an all nighter, i've finally figured out all i need to know about wiring this project.

Image
(simplified wiring chart, at least for me)

x4 470k resistors (1/4 watt but 1/8 watt and 1/2 watt should be fine)
x2 npn bipolar transistors (2N2222,2N3409,2N4401 and others)
x2 .05uf caps film or ceramic(original used ceramic and .047uf should work)
x2 .002uf caps film or ceramic (again ceramic for the original and .0022uf will work)
x1 500k linear taper pot
x1 50k audio taper pot

I ordered most of my parts from this website
http://www.fuzzboxworld.com/index.html

I ordered the ceramic capacitors from another source. And if the snow lets up tomorrow i'm going to go to radioshack and pick up the resistors,transistors, and miniboard.

User avatar
Olav
Top Producer
Posts: 321
Joined: Tue Aug 04, 2009 3:34 am
Location: Öckerö's loge
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby Olav » Mon Dec 27, 2010 3:37 am

You've been a busy boy Mike!
Looking forward to seeing you do this. Might have to go "Olav See, Olav Do" on it.
va' sa' du? va' hete' du?
my guitars @ LGTf
Official Member of the GUN Guitar Owners Association
my 2011TDPRI entry

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Wed Dec 29, 2010 7:37 pm

Image

finally started!

the first one was a bit sloppy for my taste, so i started over

Image

User avatar
Sarah93003
Master Contributor
Posts: 3812
Joined: Tue Mar 10, 2009 4:26 pm
Location: Westlake Village, CA
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby Sarah93003 » Wed Dec 29, 2010 8:08 pm

Very cool!
____________________
1965 Mosrite Celebrity Prototype with Vibramute
1972 Mosrite Celebrity-III
1977 Gibson MK-53
1982 Fender Bullet
1994 Gretsch Streamliner G3155 Custom
2005 Gibson Les Paul Standard Plus
2006 Jude Les Paul 12 String

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Wed Dec 29, 2010 9:22 pm

I have most of it wired up, im going to go drill holes in the case tomorrow, so i can fit the 9V adaptor and finish this thing up!

Image

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Thu Dec 30, 2010 12:35 pm

Victory is mine

Image

one of my volume control holes is a bit off, i think im just going to transfer it into a new box. Had a good time though, will deffo be building more of these!

User avatar
Olav
Top Producer
Posts: 321
Joined: Tue Aug 04, 2009 3:34 am
Location: Öckerö's loge
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby Olav » Thu Dec 30, 2010 2:24 pm

Taste?
va' sa' du? va' hete' du?
my guitars @ LGTf
Official Member of the GUN Guitar Owners Association
my 2011TDPRI entry

User avatar
mikethemod1992
Valued Member
Posts: 193
Joined: Wed Aug 18, 2010 4:27 am
Location: Atlanta Georgia
Contact:

Re: Having a go at building a Fuzzrite, a few questions

Postby mikethemod1992 » Thu Dec 30, 2010 2:33 pm

Olav wrote:Taste?


afraid not, i had to go to the local music store to test it. haha


Return to “Mosrite & Clone, Projects, Parts & Accessories Q&A”

Who is online

Users browsing this forum: No registered users and 42 guests